Timeout will occur if connection does not succeed within five seconds. For example to connect via COM port 1 the command will look like: connect '/C=1' Value would be saved as `ConnectingTimeout' entry in teraterm.ini file. Conversely, no action if the value is zero. Connecting to myserver could be canceled after timeout Note: This option value is connecting timeout value(per seconds). General connection connect 'myserver /timeout=' connect ' myserve /ssh /auth=password /user= username /ask4passwd'Ĭonnect ' myserver /ssh /1 /auth=password /user= username /ask4passwd'Ĭonnect ' myserver /ssh /2 /auth=password /user= username /ask4passwd'Ĭonnect ' myserver /ssh /auth=publickey /user= username /ask4passwd /keyfile= private-key-file'Ĭonnect ' myserver /ssh /1 /auth=publickey /user= username /ask4passwd /keyfile= private-key-file'Ĭonnect ' myserver /ssh /2 /auth=publickey /user= username /ask4passwd /keyfile= private-key-file'Ĭonnect ' myserve /ssh /auth=challenge /user= username /ask4passwd'Ĭonnect ' myserver /ssh /1 /auth=challenge /user= username /ask4passwd'Ĭonnect ' myserver /ssh /2 /auth=challenge /user= username /ask4passwd'Ībove 9 ways pass username and authentication method directly from macro, and the popup asks for password.
Teraterm pro command line options password#
Password or private-key-file thus you should not replace the word 'password' or the word 'publickey' in it with actual password.Ĭonnect ' myserver /ssh /auth=pageant /user= username'Ĭonnect ' myserver /ssh /2 /auth=pageant /user= username'Ībove 3 ways allow to skip popup dialog and pass username directly from macro. Or /auth=publickey or /auth=challenge is the parameter saying that authentication will be done by entering
Absiolute path does not work.Ībove 9 ways allow to skip popup dialog and pass username and password directly from macro. Note: path to /keyfile should be relative to Teraterm directory. connect ' myserver /ssh /auth=password /user= username /passwd= password'Ĭonnect ' myserver /ssh /2 /auth=password /user= username /passwd= password'Ĭonnect ' myserver /ssh /auth=publickey /user= username /passwd= password /keyfile= private-key-file'Ĭonnect ' myserver /ssh /2 /auth=publickey /user= username /passwd= password /keyfile= private-key-file'Ĭonnect ' myserver /ssh /auth=challenge /user= username /passwd= password'Ĭonnect ' myserver /ssh /2 /auth=challenge /user= username /passwd= password' Parameters /1 and /2 force to use SSH1 or SSH2 method. connect ' myserver /ssh /1' # outdated, not recommended unless absolutely necessary This way will start SSH connection without defining whether SSH1 or SSH2 has to be used. In case it was SSH than your macro will try toĬonnect via SSH and will eventually fail. Or SSH) that was used during last time when teraterm.ini file was saved. Without this parameter Tera Term will start connecting with the same method (telnet Telnet connections connect ' myserver:23 /nossh' There are 3 types of connection you can establish from Tera Term macro: To test the current link and connect status before executing the "connect" command, use the " testlink" command.Ĭommunication commands except "connect", "cygconnect" and "testlink" can not be executed before the link is established. If MACRO has already been linked to Tera Term and Tera Term has already been connected to the host, this command is ignored.Īs a result of this command, the system variable "result" is set to one of the following values depending on the linkĬonnection to the host has not been made, but link to Tera Term has been made. If MACRO has already been linked to Tera Term and Tera Term is not connected to the host, this command causes Tera Term
Msg = ':22 /ssh /auth=publickey /user=root /keyfile=RSA\id_rsa' If MACRO is not linked to Tera Term, this command runs Tera Term with, and links it to MACRO. (slightly skeptical) Educational society promoting " Back to basics" movement against IT overcomplexity Softpanorama May the source be with you, but remember the KISS principle -)